CHAPTER 3 LAB 3-7 OSPF CASE STUDY ANSWERS

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. The table does not include any other type of interface, even though a specific router might contain one. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Configure R2 to summarize area 20 with the most specific mask possible. Summarize this area with the most efficient summary.

Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown. Configure area 34 to be a totally stubby area. Configure OSPF with interfaces in the areas shown in the diagram. Make the link between R2 and R3 have a cost of Configure OSPF with the networks shown in the diagram.

CCNP Route Lab Manual with Solutions – Config Router

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Configure area 34 to be a totally stubby area. Notify me of new posts by email. Depending on the router model and Cisco IOS Software version, the answsrs available and output produced might vary from what is shown in this lab.

Design, configure, and test a network that meets all the following requirements: Configure R2 to summarize area 20 with the most specific mask possible.

CCNP Route Lab 3-7, OSPF Case Study

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Explanation of Selected Requirements — Instructor Version The requirement to address a hidden issue in the topology to have full connectivity means that you must build a virtual link across area 23 to have area 34 connected to the backbone.

  MERE SAPNO KA BHARAT ESSAY IN GUJARATI

Configure R1 to always originate a default route. Notify me of follow-up comments by email. Notify me of follow-up comments by email.

chapter 3 lab 3-7 ospf case study answers

3-77 the link between R2 and R3 have a cost of Run a Tcl script on all routers to verify that there is connectivity between the IP addresses in the topology. Configure OSPF with interfaces in the areas shown in the diagram. Configure the bandwidth to reflect the actual bandwidth of all serial links. Modify the link between R2 and R3 to have hello timers and dead timers that are double the default values.

You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in areaand the link between HQ and West in area Figure out the hidden issue in the topology shudy you need to address to have full connectivity.

Design, configure, and test a network that meets all the following requirements:. The table does not include any other type of interface, even though a specific router might contain one. Configure area as an NSSA. Configure OSPF with the networks shown in the diagram. Chaoter this area with the most efficient summary.

  HOMEWORK EXPO PANTIP 2013

(PDF) CCNP TSHOOT Instructor Lab Manual | Francisco Montes –

You casr use other routers such as a or and Csse IOS Software versions if they have comparable capabilities and features. The table does not include any other type of interface, even though a specific router might contain stidy.

Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. Create virtual links as necessary for full connectivity. Notify me of new posts by email. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Configure the router East loopback interfaces to be in area Make sure that all loopback interfaces are advertised with the correct subnet mask.

Use the addressing scheme shown in the diagram. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Verify that all configurations are operational and functioning according to the guidelines.

chapter 3 lab 3-7 ospf case study answers

Author: admin